31504376-S2300&3300&5300&6300 Installation Quick Start & 快速安装指南-(10,EN&CN)

设备附件介绍

Rubber padsCaptive nutM4 screwM6 screwLoose-proof pinch

Short rack-mounting ear

Long rack-mounting ear

胶垫贴浮动螺母

M4 螺钉M6 螺钉

防脱卡短挂耳

长挂耳

注意事项

Before installation, take ESD-preventive measures, for example, wear ESD-preventive gloves or a wrist strap.安装前请做好防静电保护措施，如配戴防静电手套或防静电手腕。

安装设备到机柜中

● The grounding cable is at one side of the S5300 except for the S5348TP-SI and S5306TP-LI-AC.Therefore, you must connect the grounding cable before the installation.

● The S6300 chassis is 420 mm in depth. To fix the S6300 chassis securely in a rack, install guide rails in the rack.

● When the 220 m depth chassis of an S2300 or S3300 is installed in a cabinet, use two screws to install the rack-mounting ear onto the chassis.● 由于S5300(除S5348TP-SI和S5306TP-LI-AC外)的接地线位置在侧面，为防止设备安装到机柜后无法安装接地线，请先安装设备接地线。● 由于S6300是420mm深的机箱，悬臂结构较长，为保证设备承重，请先安装滑道。

● S2300、S3300的220mm深机箱在机柜中安装时，安装挂耳到机箱上只需要固定2个螺钉即可。

Fix the captive nuts.安装浮动螺母。

IEC cabinet (19 inch)ETSI cabinet (21 inch)Install the device in a cabinet.安装设备到机柜。

IEC cabinet (19 inch)IEC 机柜(19寸)

IEC 机柜(19寸)

安装设备到工作台 (S6300不支持在工作台上安装)

粘贴胶垫贴。

Rubber pads

胶垫贴

安装设备到墙面

● The S6300 cannot be mounted on the wall.

● To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall.

● When the 220 mm depth chassis of an S2300 or S3300 is mounted on the wall, use two screws to install the rack-mounting ear onto the chassis.● S6300不支持挂墙安装。

● 在墙上打孔时，必须确认打孔处没有墙电，避免造成人身伤害。

● S2300、S3300的220mm深机箱挂墙安装时，安装挂耳到机箱上只需要固定2个螺钉即可。

Fix the rack-mounting ears.Install the plug bolt.安装膨胀螺栓。

M6膨胀螺栓

Install the device on the wall.Mark the hole locations on the wall according to 安装设备到墙面。

the device installed with rack-mounting ears.

根据已安装挂耳的设备，用记号笔标记打孔位置。

模块的安装与拆卸

All the power supplies and fan modules are hot swappable, but other service modules are not hot swappable, except those of S5328C-HI and S5328C-HI-24S.电源和风扇模块支持热插拔，其他业务模块不支持（除S5328C-HI和S5328C-HI-24S外）。

Installation of the power supply module.Removal of the power supply module.安装电源模块。拆卸电源模块。

第1页下一页